JC-RTTC-10 electric soil sampler

1、 Product Introduction
JC-RTTC-10 electric soil sampling rig is a lightweight soil sampler designed based on reference to large hydraulic, gasoline, and pneumatic drilling rigs. Even inexperienced drilling personnel can operate with simple training. The sampling process is extremely simple, and only 1 to 2 people can complete the operation of the equipment. The entire drilling process does not require adding water, ensuring the quality of the sample obtained (no pollution, no disturbance).
Compared with conventional large drilling rigs, the JC-RTTC-10 electric soil sampling drilling rig is more convenient to carry, easier to operate, and can be easily operated by non professionals. In some project sites with low depth requirements (within 10 meters), relatively complex terrain, and difficult access for large equipment, using this equipment is a good choice.
Compared with traditional hand drills, the JC-RTTC-10 electric soil sampling rig has a deeper sampling depth, higher sampling efficiency, and obtains undisturbed and compressed (depending on the terrain) soil samples. In projects with sampling depths exceeding half a meter and high requirements for soil sample quality (undisturbed, non compressed), using this equipment is a good choice.
2、 Product parameters
1. Electric host:
Voltage: 220V
Power: 3.6KW
Ignition method: switch type
Energy consumption: low energy consumption
Impact frequency: 2600/M
Impact energy: 60J~79J
Core depth: 0-10M
Host weight: 22KG
2. The standard sampling drill rod should not be less than 2 meters, and the drill rod can be moderately increased according to actual work needs;
3. Sampling depth, can be connected to a drill rod for one-time sampling without lifting the drill halfway;
4. Drill rod: inner and outer diameter not less than 38mm/50mm; Length not less than 1.00 meters per piece, using threaded connections, easy to assemble and disassemble;
5. Drill bit: Take one hard soil drill bit and one standard soil drill bit each;
6. Sample tube: inner and outer diameters not less than 34mm/35mm; The length shall not be less than 1.00 meters per piece; Equipped with gaskets;
7. Pulling device: Fast pulling, with a speed of not less than 3.00 meters per minute, adopting a more reasonable ergonomic design, which can be pressed by hand or stepped on by foot;
8. The instrument is a portable on-site sampling device suitable for vehicles.
3、 Standard configuration
1. 1 electric host
2. Standard soil drill bits and hard soil drill bits can be freely selected and matched
3. Two 1-meter drill rods
4. 1 set of auxiliary extraction device
5. Plastic sleeve, length 1 meter, inner diameter 35mm, equipped with related gaskets and accessories
6. One industrial plastic transport box
7. 1 scraper, rubber hammer, pliers, headphones, 5M tape measure, gloves, and cleaning brush each
8. Product manual
9. Product Qualification Certificate
10. Instrument Warranty Card
4、 Application direction
1. Agricultural/Forestry Soil Investigation
2. Environmental Soil Investigation
3. Geotechnical Engineering Investigation
4. Groundwater investigation
5. Coastal geological survey
6. Wetland environmental investigation
7. Investigation of tailings pond and storage yard
8. Archaeological investigation

Juchuang Environmental Protection provides you with comprehensive technical support and perfect after-sales service! Details consultation:!

1. Electric host:
Voltage: 220V
Power: 3.6KW
Ignition method: switch type
Energy consumption: low energy consumption
Impact frequency: 2600/M
Impact energy: 60J~79J
Core depth: 0-10M
Host weight: 22KG
2. The standard sampling drill rod should not be less than 2 meters, and the drill rod can be moderately increased according to actual work needs;
3. Sampling depth, can be connected to a drill rod for one-time sampling without lifting the drill halfway;
4. Drill rod: inner and outer diameter not less than 38mm/50mm; Length not less than 1.00 meters per piece, using threaded connections, easy to assemble and disassemble;
5. Drill bit: Take one hard soil drill bit and one standard soil drill bit each;
6. Sample tube: inner and outer diameters not less than 34mm/35mm; The length shall not be less than 1.00 meters per piece; Equipped with gaskets;
7. Pulling device: Fast pulling, with a speed of not less than 3.00 meters per minute, adopting a more reasonable ergonomic design, which can be pressed by hand or stepped on by foot;
8. The instrument is a portable on-site sampling device suitable for vehicles.