Korsen high-pressure vortex fan, air pump, industrial dust removal and suction blower

Korsen high-pressure vortex fan, air pump, industrial dust removal and suction blowerWorking Principle:
Vacuum suction high-pressure fanIt's usinghigh-pressure blowerThe high-speed operation of the impeller generates suction and pressure, which creates a local vacuum inside the dust collector: 2. Under the action of suction and pressure, air is discharged at high speed, and the air in the suction part at the front end of the high-pressure fan continuously supplements the air in the fan, causing an instantaneous vacuum inside the vacuum cleaner and forming a negative pressure brush with the external atmospheric pressure. Long connecting pipes, hoses, bent pipes, hose joints enter the dust filter bag, and dust and other debris are trapped in the dust filter bag. After being purified by the filter, the air is discharged from the exhaust outlet at the tail of the organism! 3. High pressure fans use suction power in industrial vacuum cleaners to create air circulation and vacuum, collecting dust and other debris through pipes.

Vortex high-pressure fanUsage and maintenance:

1. The air pump should be placed in a relatively stable place, and the surrounding environment should be clean, dry, and well ventilated.

2. The rotation direction of the air pump impeller must be in the direction indicated by the arrow on the fan casing.

3. When the air pump is working, it should be avoided that the inlet and outlet of the fan are sealed to prevent excessive heat generation and motor overcurrent that may cause damage to the air pump.

4. Except for the two bearings of the motor rotor, there is no direct contact friction in other parts of the air pump.

5. The filter screens at both ends of the inlet and outlet should be cleaned in a timely manner according to the situation to avoid clogging and affecting use.

6. The external connection of the inlet and outlet must be made using flexible hoses (such as rubber hoses or plastic spring hoses).

7. Bearing replacement: Bearing replacement must be carried out by personnel familiar with repair work. First loosen the screws on the pump cover, and then disassemble the parts one by one according to the order shown in the diagram. The disassembled parts should be cleaned, and then assembled in reverse order. When disassembling, do not forcefully pry the impeller, use a roller to remove it, and do not miss the adjusting gasket to avoid affecting the clearance that has been adjusted before leaving the factory.

8. It is strictly prohibited for solids, liquids, and corrosive gases to enter the pump body.

The commonly used ones on the market are single impeller and double impeller
Special vortex fans: explosion-proof vortex fans, variable frequency vortex fans, corrosion-resistant vortex fans, DC vortex fans, high-temperature resistant vortex fans, fully sealed vortex fans, pump heads without motors (i.e. drag pumps), or combination air pumps of two of them, to meet different application scenarios and working conditions of customers.
4、 Advantages of vortex fan
　　1It has dual functions of blowing and suction, and can be used for vacuum adsorption, blowing and conveying, as well as closed circuit air circulation.
　　2Oil free operation, the output air is clean because the fan relies on electricity input for operation, and there are no oily components inside, so there is no need to worry about air pollution during transportation, and no impurities will be produced.
　　3High pressure and powerful, compared to centrifugal fans and medium pressure fans, its pressure is much higher, which determines the pressure problem that other fans cannot meet. Moreover, it has a small volume, low sound, and will not cause noise pollution.
　　4The pump body is made by integral die-casting using a hydraulic press, and is equipped with shockproof mounting feet. Therefore, its requirements for the installation foundation are also very low, and it can even operate normally without fixing the feet.

Wear resistant measures for fans:
(1) The serrated middle plate of the high-pressure blower can not only improve the airflow distribution at the impeller outlet and reduce GD2, but also avoid the erosion of the middle plate by flue gas;
(2) The high-pressure blower blades are equipped with replaceable wear-resistant lining plates (with tungsten carbide welded on the surface of the lining plates);
(3) The replaceable conical disc protects the middle disc from wear and tear;
(4) The casing is equipped with scroll liners and side liners;
(5) The surface of the high-pressure blower is coated with ceramic wear-resistant coating, resin coating, quartz powder and water glass coating, etc;
(6) Surface strengthening treatment includes surface welding, thermal spraying, boronizing, laser surface hardening, and high-frequency quenching.

Double bladed high-pressure blower Installation precautions:
1. Installation location: It must be installed indoors in a place that is not affected by wind and rain;
2. Environmental temperature: below 40 ℃;
3. Relative humidity: below 80%;
4. Air quality: If there are corrosive or flammable gases such as acids and alkalis in the air, they should not be transported by high-pressure blowers to avoid danger
5. Dust protection: Avoid using in places with large amounts of dust, powder, or fibers. If it is necessary to use in such places, please install a filter and regularly clean the dust attached to the filter and inside the high-pressure blower;
6. Ventilation and heat dissipation: Please choose to use it in a well ventilated place and not in a sealed room or box;
7. Placement space: For the convenience of column maintenance or repair, please avoid installing in overly narrow locations.

Double bladed high-pressure blowerUsage detection method:
1. Check the fastening condition of each part and whether there is any looseness in the positioning pin
2. There is no oil leakage inside the blower body
3. There should be no scaling, rusting, or peeling inside the blower body
4. Pay attention to whether the lubrication and heat dissipation are normal, pay attention to the quality of the lubricating oil, regularly listen to the operation of the blower for any noise, pay attention to whether the unit is running under non compliant working conditions, and regularly add butter
5. The overload of the blower is sometimes not immediately displayed, so attention should be paid to the increasing trend of the intake and exhaust pressure, bearing temperature, and motor current to determine whether the machine is running normally
6. Before disassembling the machine, the dimensions of each fitting should be measured, recorded, and marked on the components to ensure that the original fitting requirements are maintained after assembly

Korsen high-pressure vortex fan, air pump, industrial dust removal and suction blowerIntroduction to industrial applications:

1. Textile equipment: vortex air pump, high-speed sock weaving machine; Coating thickness control and ensuring uniform thickness, removing moisture, drying, and yarn drawing machine.
2. Plastic auxiliary equipment and feeding system: In the use of the casting machine, in order to ensure high-speed production and uniform casting film, the air knife on the cooling roller forms a thin layer of air between the film and the surface of the cooling roller, and the vortex air pump cools the film evenly; Simultaneously used for vacuum feeding, drying, dehumidification, and feeding systems in injection molding machines.
3. Computer monitors, LCD monitors, printed circuit boards, and other products can be used in printed circuit board equipment such as vortex air pump cleaning, water cutting, and drying.
4. In wire and cable equipment, it can remove moisture, oil, dry, and suppress static electricity, such as removing water from precision copper pipes for air conditioning.
5. Effective control of coating thickness and ensuring uniform thickness in painting equipment; Can dry, remove moisture, dry at high temperatures over a large area, and control coating thickness; After electroplating, metal surface treatment such as cutting, drying, and degreasing.
6. High pressure vortex fan is used for pneumatic conveying of cans; The use of cutting water, drying, and other food and beverage filling equipment before coding or labeling beverage bottles, cans, and various packaged foods.
7. Printing equipment: screen printing machinery; UV polishing machine, instant drying of ink within 1-5 seconds after printing.
8. Air treatment equipment that can be used for the collection, purification, and recycling of toxic and harmful gases; Gas detection equipment for atmospheric environment.
9. Specially suitable for cleaning equipment such as ultrasonic cleaning machines, PCB board cleaning and drying machines in the electronics industry, tunnel type car cleaning machines (car washing machines), commercial dishwashers, glass cleaning machines, etc.
10. High pressure vortex fans can be used for surface aeration, oxygenation, oxygenation grids, and oxygenation systems in fish farming.
11. Used in tires and rubber equipment to remove moisture/oil, dry, and suppress static electricity