SPA1007LW imported triangle belt

SPA1007LW imported V-belt, anti-static V-belt, imported V-belt, high temperature resistant V-belt, air conditioner belt, high-speed oil proof V-belt, fan belt, anti-static V-belt, the other several should be replaced at the same time and cannot be used together with new and old belts. Cleaning of the belt. When the V-belt is stained with grease, engine oil and other oil stains, it is easy to slip and accelerate the damage of the V-belt. It should be cleaned with gasoline or alkaline water in a timely manner, and cannot be operated with oil\\

A narrow anti-static V-belt with a width of *, designed for high-speed transmission.

D-type bandwidth 31.5mm with height 19.0mm rubber standard model D-group model RD

Gates Details in the United States

Among them, the 3VX type has a bandwidth of 9.9 millimeters, a height of 8.7 millimeters, and an angle of 38 degrees

Wide angle belt: 3M, 5M, 7M, 11M FREESPAN BELT synchronous conveyor belt

Ordinary V-belt: M-type, A-type, B-type, C-type, D-type, E-type

E-type bandwidth 31.5mm with height 19.0mm Rubber standard model E-group model RE

A-type bandwidth 12.5mm, height 9.0mm, rubber standard model, A-section with teeth model, AX combination model, RA, RAX

Table type synchronous belt (trapezoidal square teeth): MXL, XL, L H, XH, XXH

K. M, A, B, C, D, E type ordinary triangle belt flat belt FL, FM, FH

Polyurethane synchronous belt: T80, T5, T10 Okinawa V-belt (universal belt) M, A, B, C and buckle

Poly Chain GT2 (polyurethane synchronous belt): 8GT2, 14MGT2

Standard V-belt, commonly known as ordinary V-belt

A combination refers to a machine belt formed by the parallel connection of multiple standard models or sliced toothed models. A combination belt can be formed by the parallel connection of 2, 3, 4, or 5 belts.

Ordinary triangle belt: A, B, C

5V type with a bandwidth of 16.0mm and a height of 13.5mm, angle of 40o. Rubber standard model, 5V slice with teeth model, 5DX combination model, R5V, R5VX

Our company is a professional agent and seller of imported industrial belts, synchronous belts, etc.

Circular toothed synchronous belt GT: 1GT, 1.5GT, 2GT, 3GT, 5GT Multi groove belt: PJ, PL, PM Wheel

3V type with a bandwidth of 9.5mm and a height of 8.0mm, angle of 40o. Rubber standard model 3V, sliced with teeth model 3VX, combined model R3V, R3VX

B-type bandwidth 16.5mm, belt height 11.0mm, rubber standard model, B-section with teeth model, BX linkage model, RB, RBX

Loading and unloading of SPZ487LW imported V-belt. Before installation, first check whether the driving wheel, driven wheel, and tensioning wheel are on the same plane. Generally speaking, when the center distance between two pulleys is less than 1 meter, the allowable deviation is 2-3 millimeters, and when the center distance is greater than 1 meter, the allowable deviation is 3-4 millimeters. If the deviation is too large, it should be adjusted to meet the requirements before installation and tensioning. When loading and unloading, the tensioner should be loosened first, or the infinitely variable speed end disc should be removed first, and the belt should be installed or removed. When the new V-belt is too tight and difficult to install and remove, the pulley should be removed first, and then the V-belt should be fitted or removed before installing the pulley. Hard removal is not allowed. Generally, the V-belt should be disassembled and installed after removing the pulley. The tension of the belt. The tension of the transmission belt is adjusted by the tensioning wheel. If the belt is too tight, it will cause serious wear and tear, and if it is too loose, it is easy to slip, causing serious wear and even burning of the V-belt. When the distance between two wheels is about 1 meter, press the middle of the triangle belt with your fingers and it should descend vertically by 10-20 millimeters. During use, the tension of the V-belt should be checked and adjusted at any time. Belt replacement. After the effectiveness of the V-belt, it should be replaced in a timely manner. If multiple V-belts are used together, if one or part of them are ineffective, the other ones should be replaced at the same time, and new and old belts should not be used together. Cleaning of the belt. When the V-belt is stained with grease, engine oil and other oil stains, it is easy to slip and accelerate the damage of the V-belt. It should be cleaned with gasoline or alkaline water in a timely manner, and cannot be operated with oil. The working temperature of the belt.