Ultrasonic cleaning using vortex air pump blower

Ultrasonic cleaning using vortex air pumpPerformance and Features:
1. Beautiful surface
2. Special blade design, high airflow, low noise, and long lifespan.
3. Using aluminum alloy material, significantly reducing weight and achieving the goal of lightweighting.
4. The motor is a fully enclosed external fan type aluminum frame motor with a special axis design, which can be used for a full length of time.
5. Low maintenance and long-life lubricating grease for cooler operation bearings, 100% oil-free air
6. A higher pressure ratio is generally suitable for wide voltage motors operating at 50/60Hz/86Hz.
7. Wide performance range, complete variety of styles, and abundant inventory!? (Can replace all fans of the same type)
8. Special air volume control damper, with high stability in air volume control and easy operation
9. No vibration, therefore complete dynamic stability
10. Easy to install, can be installed in any direction along the axis
11. Can work continuously for 24 hours without interruption
12. The blades and covers of the high-pressure fan are made of the world's hardest ADC12 material, equivalent to the same material as Mercedes Benz wheel rims.
13. The bearings of the high-pressure fan adopt high-speed and high temperature resistant imported NSK bearings, which can rotate at 2800 revolutions per minute at 50Hz and 3450 revolutions per minute at 60Hz, without lubrication and maintenance for 20000 hours, equivalent to continuous operation for 2 years.
14. The high-pressure fan has two functions: air supply and suction. It adopts Siemens technology and passes gas that is oil-free and dry. The high-pressure fan is suitable for auxiliary equipment in multiple mechanical industries.

Ultrasonic cleaning using vortex air pumpMalfunctions and troubleshooting methods;
（1） The fan does not rotate
1. Not connected to power supply - connected to power supply
2. Motor not working - check motor wiring or replace motor
3. Damaged fan head - repair or replace the fan
4. Foreign objects stuck in the fan - remove foreign objects
（2） Increased noise
1. Bearing dry lubrication - adding bearing grease
2. Bearing damage - replace the bearing
3. Impeller wear - replace impeller or pump head
4. Loose or detached sturdy components - tighten the fasteners tightly
5. There are foreign objects inside the fan - remove the foreign objects or replace the pump head
（3） Increased vibration
1. Bearing damage - replace the bearing
2. Unbalanced impeller - remove foreign objects from the impeller or calibrate the dynamic and static balance
3. Spindle deformation - replace spindle or pump head
4. Entering the turbulent zone in the working state - adjust the working state to avoid the turbulent zone
5. The inlet and outlet filter screens are blocked - clean the filter screen
（4） Temperature increase
1. Inlet temperature too high - reduce inlet temperature
2. Bearing dry lubrication - adding bearing grease
3. Fan efficiency decreases - remove blade dust or replace pump head
4. Change in work status - adjust work status
5. Environmental temperature increase - increase ventilation and heat dissipation in the environment
（5） Reduced pressure
1. Pump head speed reduction - low power supply voltage or motor failure
2. Increased pipeline resistance - reducing pipeline resistance
3. Change in work status - adjust work status
4. Motor direction reversed - motor rewiring
（6） Decreased traffic
1. The inlet and outlet air filters are clogged - clean the filter
2. Pump head speed reduction - low power supply voltage or motor failure
3. Increased pipeline resistance - reducing pipeline resistance
4. Increase in work status - adjust work status
5. Motor direction reversed - motor rewiring

The main reasons for vibration are as follows:
1、 The coupling is not aligned, that is, the center is not adjusted properly,
2、 The bearing is severely damaged, causing vibration,
3、 There is wear and tear between the impeller and the casing,
4、 Loose or poorly grouted anchor screws,
5、 During operation, there is a high or excessive amount of dust that adheres to the blades,
6、 After the impeller wears out, an unbalanced component is generated.