XMC pulse single machine dust collector

NegotiableUpdate on 01/29

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Introduction to XMC Pulse Single Machine Dust Collector: The XMC pulse single machine dust collector adopts the technology of high-pressure (0.5~0.4MPa) high flow pulse valve to blow and clean the dust filter bag one by one

Product Details

The XMC pulse single machine dust collector adopts the technology of high-pressure (0.5~0.4MPa) high flow pulse valve to blow and clean the dust filter bag one by one. Capable of collecting over 99.9% of dust from a large amount of ultrafine dust (particles of £ 5 μ m, with a content of over 70%) and high concentration (1300g/m3n) gases. At the end of 1997, the dust collector passed provincial appraisal and was found to have the highest level in China, with its main technology being the first of its kind in the country. At present, under the new national environmental protection standards, it is widely used not only for dust control in cement plants, but also in the field of deep processing of non-metallic mineral fines. It also has good application prospects in industries such as power, chemical, metallurgy, and steel.

The XMC pulse single machine dust collector can be combined with various specifications of dust collectors according to different specifications of solenoid valves. This series of dust collectors can operate under negative or positive pressure without any changes to its body structure, and the dust collection efficiency reaches 99%. Above 8%, the purified gas has a dust concentration of less than 100mg/m3. If this series of dust collectors is used in cold regions or when the flue gas is below zero, insulation and heating devices need to be added, and the shell should also be changed accordingly.

Attention to the operation of XMC pulse single machine dust collector:

(1) When starting the XMC pulse single machine dust collector, the compressed air should be connected to the air storage tank first, the control power should be connected, and the ash discharge device should be started. If there are other equipment in the system, downstream equipment should be started first.

(2) When the XMC pulse single machine dust collector is shut down, there is no need to cut off the compressed air source, especially when the fan is working, compressed air must be provided to the lift valve cylinder to ensure that the lift valve is in the open state.

(3) The oil-water separator in the air storage tank and gas source triple component should be discharged once per shift, and the industrial dust collector oil-water separator should be cleaned every 3-6 months. The oil mist generator should be checked for oil storage regularly and refilled in a timely manner.

(4) If the XMC pulse single machine dust collector malfunctions, it should be promptly eliminated. If there are impurities or moisture inside, it should be cleaned. If the membrane is damaged, it should be replaced in a timely manner.

(5) When the XMC pulse single machine dust collector is working normally, the ash discharge device cannot stop working. Otherwise, the ash hopper will quickly accumulate dust and overflow into the bag chamber, forcing the industrial dust collector to stop working.

(6) The XMC pulse single machine dust collector regularly measures process parameters such as smoke volume, temperature, concentration, etc. If any abnormalities are found, the cause should be identified and dealt with in a timely manner.

(7) Management personnel should be familiar with the principles, performance, and operating conditions of industrial dust collectors, and master adjustment and maintenance methods.

(8) When shutting down, after the process system stops, the industrial dust collector and exhaust fan should continue to work for a period of time to remove moisture and dust from the dust removal equipment. It must be noted that when the industrial dust collector stops working, it must be repeatedly cleaned (manually) to remove dust from the dust removal filter bag to prevent it from being affected by moisture and sticking to the bag.

(9) The mechanical moving parts such as the reducer and ash conveying device of the XMC pulse single machine dust collector should be oiled and changed according to regulations. Any abnormal phenomena should be promptly eliminated.

(10) The XMC pulse single machine dust collector uses a timed cleaning controller, and the cleaning cycle should be regularly measured to ensure accuracy. Otherwise, adjustments should be made. When using a fixed resistance pulse controller, the working condition of the pressure switch should be checked regularly,