500N. m torque wrench calibrator, calibrated torque wrench tester

500N. m torque wrench calibrator, calibrated torque wrench tester

look for500N. m torque wrench calibratorMy friend came to the weighing factory to cast this SGCMY series produced by our factory500N. mTorque wrench calibratorIt is a testing instrument used to verify torque wrenches, with strong hardware expandability and software Flexible platform. The torque wrench tester has the characteristics of real-time display, dial display, curve display, etc. The torque wrench calibration device has been applied in manufacturing industries and testing departments such as power, light industry, machinery, engines, internal combustion engines, electric vehicles, motorcycles, automobiles, ships, airplanes, etc.

500N. m torque wrench calibratorimage

Torque wrench calibratorSpecification Model

500N. m torque wrench calibratorpurpose

Mainly used for testing fixed torque wrenches, digital torque wrenches, preset torque wrenches, torque screwdrivers, screwdrivers, and instruments and products related to tightening force.

500N. m torque wrench calibratorFeatures

1. High precision, high resolution, fast sampling speed, full screen display.

2. Adopting high-precision torque sensors with torque direction reminders.

3. 7-inch touchscreen display with peak hold function.

4. Four units are interchangeable and available for selection (N · m, kgf · cm, lbf · in, lbf · ft).

5. The real-time and peak modes can be switched freely.

6. Real time display, dial display, curve display.

7. Real time display of time,.

8. Set up reminders for upper and lower torque values.

9. It can store peak data, and the data stored inside can be viewed or exported from a USB drive.

10. The interface displays in both Chinese and English, and can be freely switched according to needs.

11. Corresponding numbers can be set according to the torque wrench.

Torque wrench calibratorLCD touch screen display interface diagram:

Switch between Chinese and English

The main interface displays:

Curve and pointer display interface:

Data storage interface:

500N. m torque wrench calibratorfunction key

a、 Unit key. When the current unit cannot test the requirements, click on the unit position to display the units in sequence

（N·m、kgf·cm、lbf·in、lbf·ft）， Can be switched alternately.

b、 Peak key, default to real-time value. If peak value is needed, click on it and switch between real-time and peak values alternately.

c、 Zero key, press this key in real-time to return to zero position.

d、 Switch key, press this key to enter the dial and curve display interface.

e、 The storage key can store the current value, and the view key can be used to query the stored data.

F、 Menu button, enter menu button, can calibrate and debug the device (non personnel cannot enter casually)

2. Power interface: Connect the instrument to a power source (this instrument can be directly plugged into a 220V power source).

3. Load bearing square hole: connected to the square measuring head of the tested object.

4. Tested objects: such as dial torque wrenches, preset torque wrenches, etc.

5. Handwheel: Rotate the handwheel to perform the inspection.

500N. m torque wrench calibratorComponent composition

Plan schematic diagram of SGCMY series torque wrench tester:

1. Sensor force head: At the factory, several conversion test heads are equipped according to the size of the torque wrench square head, which are connected to the square measuring head of the tested object;

2- Display: The touch screen display window can set and display torque values, etc;

3- Horizontal force rod;

4- Screw;

5-Height adjustment knob: The platform height can be adjusted to keep the torque wrench being tested in a horizontal state. If it is not in a horizontal state, it may cause measurement errors; Left and right adjustment buttons: Adjust the testing platform to fit the arm length of the torque wrench being tested, and also adjust the direction of the testing platform to adapt to the forward and reverse measurement of the torque wrench;

6-Drive handwheel: Load or unload the tested torque wrench in both directions;

500N. m torque wrench calibratorworking environment

1. Operating temperature: -10 ℃~40 ℃.

2. Operating humidity: ≤ 90% RH.

3. There is no vibration source or corrosive environment around.

8、 Operation steps

1. Connect the power cord and insert it into the load-bearing square hole.

2. Turn on the hard switch.

3. Place the tested object in place and place the square probe of the tested object into the load-bearing square hole of the verification instrument.

4. The tail of the tested object does not touch any foreign objects, adjust the height and length adjustment blocks, and reset the display screen.

5. Shake the handwheel to start the inspection.

6. To change units during testing, press the 'Unit Switch' button to switch between the four units, and press once to switch one unit.

The size of the bearing square hole of the 500N. m torque wrench calibrator should not be collided with at will to avoid damage. The following is a plan view of the load-bearing square hole:

Service commitment:
Shanghai Zhuheng Electronics has a business philosophy of "comparing quality with domestic products, price with quality, and service with price"
Our service tenet: practical spirit, high-quality domestic products, low prices, and excellent service.
Our service has three guarantees: quality, time, and price.
We solemnly promise to provide high-quality domestic products, excellent quality, low prices, and comprehensive services.

Guess you still like:SGSX-1000 digital torque wrench Fixed torque electric wrench Digital torque meter tension tester Digital dynamometer Torque detector standard force gauge secure pak Spring tension testing machine Torque wrench tester Fixed torque wrench Digital torque tester Bottle cap torque tester Price of torque wrench Specification and model of torque wrench

500N. m torque wrench calibrator, calibrated torque wrench tester