All terrain remote control tracked self-priming mobile pump truck

All terrain remote control tracked mobile pump truckRemote control of mobile pump trucks, remote control of self-priming mobile pump trucks

Most of the mobile pump trucks currently in use are directly loaded onto tractors or cars, usually relying on the rolling of the wheels to drive their movement. Their adaptability to roads is limited, and encountering special roads with mud or many puddles can easily cause the wheels to sink and unable to continue moving. At the same time, most existing mobile pump trucks require manual operation, which has significant limitations in use and reduces their adaptability.

To achieve the above objectives, the following technical solutions are provided:Crawler self-priming drainage robotIt includes a base, a protective shell, a track chassis, a self-priming pump, a power system, and a control system. The protective shell is fixed at the top of the base, and a groove is opened at the head position of the protective shell for the fixed installation of the self-priming pump. The track chassis is installed at the bottom of the base, and the power system and control system are both set in the inner cavity of the protective shell;The water pump we are going to introduce below—Self propelled self-priming pump, with a tracked chassis, can adapt to various road conditions, complex terrains, etc. It has automatic power output, reducing the situation where it could not be used due to lack of electricity or other power sources in the past.

All terrain remote control tracked self-priming mobile pump truckphysical photo

Remote control of mobile pump truckSpecial suction head for floor area water distribution

Remote control of self-priming mobile pump truckMultiple pumps can be connected in series for boosting

Self suctionStructural diagram of remote control drainage robot

Remote control of self-priming mobile pump truckperformance parameters

1Rated flow rate of water pump: 500-1000m³/h； By particle diameter of 75-100mm

2Rated head:12 meters; Maximum lift of 30 meters

3Suction process:9m；

4The water pump is equipped with a waterless dry running protection system, which protects the impeller of the water pump from damage to the mechanical seal, impeller, and pump chamber in the absence of high-speed liquid rotation inside the pump chamber;

5The material of the pump body is adoptedHT cast iron,High toughness and plasticity. At low temperatures, toughness transitions to brittleness, but the low-temperature impact value is relatively high, and there is a certain degree of resistance to temperature induced changes and corrosion resistance；

6The centrifugal pump shaft and impeller are made of precipitation hardened austenitic stainless steel,It has comprehensive properties such as high strength, high toughness, high corrosion resistance, high oxidation resistance, and excellent formability and weldability;

7The maximum diameter of particles that can pass through the impeller100mm;

8Configure a vacuum assist system, use a rotary vane vacuum pump for the vacuum pump that does not require water cooling, run the self-priming pump and vacuum pump simultaneously when turned on, and have an automatic start stop function. When the self-priming pump discharges water, the vacuum pump will automatically stop. When the negative pressure in the inlet pipeline of the self-priming pump is low, the vacuum pump will automatically start, replacing the drawbacks of the original vacuum assisted self-priming pump in the market, which always works together with the self-priming pump. This can easily lead to damage caused by water ingress and fatigue operation of the vacuum pump.

9After starting the engine, the vacuum pump and water pump work simultaneously;

10Equipped with a fully automatic vacuum assist system100% guarantee that there will be no water entering the vacuum pump chamber, causing malfunction or damage;

11After the water pump is equipped with a vacuum assist system, the water discharge time only needs to be adjusted under maximum suction working conditions30s；

12The vacuum assisted self-priming device does not require an additional power source and is connected to the engine tail shaft via a belt. An electronic clutch is set between the belt pulley and the vacuum pump, which is connected to the automatic controller. The automatic controller has a liquid level sensor connected to the water tank at the upper end of the self-priming pump. When water is detected, it feeds back a signal to the controller to control the clutch to separate from the vacuum pump belt pulley. After separation, only the clutch and engine start simultaneously;

13The suction range can be achieved with the assistance of a vacuum pump9m。

A single self-priming pump can achieve its own suction rangeWhen the vacuum assist fails, filling the pump with water can also self suction up to 8 meters high.

All terrain remote control tracked mobile pump truckSize chart

The certificate is as follows: