Electric cast iron copper inlaid gate

Electric cast iron copper inlaid gate
Product Overview
Electric cast iron inlaid copper gate, ZMQY electric cast iron inlaid copper round gate, ZMQF electric cast iron inlaid copper square gate, ZSQF electric wall type bidirectional cast iron inlaid copper gate, electric flange cast iron inlaid copper gate, SYZ electric inlaid copper gatecast ironGate, ZMF electric cast iron copper inlaid square gate, ZMQY-I electric circular gate, electric concealed rod cast iron copper inlaid gate,Electric circular cast iron inlaid copper gate, flashlight dual-use cast iron inlaid copper round gate, ZMY electric cast iron inlaid copper round gate, flashlight dual-use cast iron inlaid copper round gate, electric cast iron inlaid copper two-way water stop round gate, electric circular cast iron inlaid copper gate, electric cast iron inlaid copper round gate, electric cast iron round gate, ZMF circular cast iron inlaid copper electric gateIt is composed of an electric belt with a manual actuator, a hoist, and a cast iron copper inlaid circular gate. The door frame and gate are both made of high-quality gray cast iron or ductile iron. The guide rails are symmetrically arranged on both sides and connected to the two ends of the door frame with stainless steel bolt positioning pins (for small and medium-sized gates, the guide rails can be cast as a whole with the door frame). The length of the guide rail is generally 1/2 to 1/3 of the full opening height of the gate, so the overall structural strength is high, rigidity is high, wear resistance, corrosion resistance is good, and pressure bearing capacity is large. The gate plate is a water blocking component that directly bears water pressure, and the gate frame is the supporting component around the gate plate. It is also the sliding track for the up and down movement of the gate plate. The outer part of the sliding track is embedded in the second phase concrete of the gate pier and gate bottom, evenly transmitting the water pressure borne by the gate plate to the gate pier and gate chamber bottom. The contact area between the upstream face of the gate frame and the downstream face of the gate frame is mechanically refined and polished to be straight, smooth, and tightly fitted, so that the joint surface, water stop surface, and motion slide are integrated into one. Widely used in urban water supply and drainage, metallurgy, petroleum, chemical, irrigation, power, textile and other industries for water treatment structures, to achieve flow and liquid level control is an important equipment for water supply and drainage and sewage treatment. Mainly installed at pipeline entrances and intersecting shafts, sedimentation tanks, settling tanks, diversion channels, pump station inlets, etc.

Main component materials of cast iron inlaid copper gate:

Cast iron copper inlaid gateTechnical Specifications:

Screw type opening and closing machineInstallation, commissioning and maintenance:

1. Be sure to maintain the basic layout plane at a horizontal angle of 180 degrees; The contact area between the base of the hoist and the foundation layout plane should reach over 90%; The screw axis should be perpendicular to the horizontal plane measured on the gate platform; It should be aligned vertically with the lifting ear hole of the gate plate to avoid tilting the screw, which may cause local stress and damage to the machine parts.

2. Place the hoist in the installation position. Put a limit plate on the screw, screw the screw into the hoist from the lower part of the crossbeam, and when the screw is exposed from above the hoist, then put on the limit plate. The lower part of the screw is connected to the gate.

3. The installation of the foundation building for the hoist must be stable and safe. The concrete for the machine base and foundation components shall be poured according to the drawings. When the concrete strength does not reach the design strength, it is not allowed to remove or change the temporary support of the hoist, nor to conduct trial mixing and operation.

4. Install the hoist according to the lifting centerline of the gate, align the center so that the deviation of the longitudinal and transverse centerlines does not exceed plus or minus 3mm, and the elevation deviation does not exceed plus or minus 5mm. Then pour the second phase concrete or connect it with the embedded steel plate.

5. The installation of electrical equipment for the hoist shall comply with the provisions of the drawings and instructions, and all electrical equipment shall be reliably grounded.

6. After the installation of each hoist, clean it, repair any damaged protective paint, and apply lubricating grease.

Precautions for installation of cast iron inlaid copper gate:

1. Reserve installation positions for gates and hoists according to the requirements in the pre embedded diagram;

2. Use a plumb bob to embed the embedded parts in a straight line, ensuring that their surface and verticality are within the range of 1.5~3 ‰;

3. Fix the door frame and guide rail onto the embedded parts with bolts;

4. When the slenderness ratio of the screw (lifting rod length/screw outer diameter) 4H/d>200, a shaft guide frame should be installed, and the distance between the shaft guide frame and the gate lifting ear should be greater than the limit opening degree of the gate.

Main external connection dimensions of cast iron copper inlaid round gate: Unitmm

Cast iron copper inlaid square gateMain external connection dimensions: Unit: mm

Note: The above product introduction, parameters, images, and data are for reference only
【ZMYElectric cast iron copper inlaid round gate, ZMY cast iron copper inlaid gateelectricGate, ZSQF electric wall type bidirectional cast iron inlaid copper gate, electric flange cast iron inlaid copper gate, SYZ electricCopper inlayCast iron gate, ZMQF electric cast iron inlaid copper square gate, ZMQY-I electric circular gate, electric concealed rod cast iron inlaid copper gate,Electric circular cast iron inlaid copper gate, flashlight dual-use cast iron inlaid copper round gate, electric cast iron inlaid copper round gate, flashlight dual-use cast iron inlaid copper round gate, electric cast iron inlaid copper two-way water stop round gate, electric circular cast iron inlaid copper gate, electric cast iron inlaid copper round gate, electric cast iron round gate, ZMF circular cast iron inlaid copper electric gate】Produced by Henan Hugao Valve Materials Co., Ltd., our company is a modern comprehensive valve enterprise specializing in the field of valve fluid control, integrating research and development, design, sales, and service. Always adhere to the business principle of "people-oriented, integrity-based". Adhering to the principle of "winning reputation with service and winning the future with quality". Looking forward to working hand in hand with you for a win-win situation.