High pressure aeration blower for slaughterhouse wastewater treatment

High pressure aeration blower for wastewater treatment in the field
High pressure aeration blower for slaughterhouse wastewater treatmentPrinciple isWhen air is blown into a water body by a high-speed rotating pump wheel, due to centrifugal and inertial effects, the air at the pump wheel outlet f obtains sufficient kinetic and potential energy to radiate and diffuse in a direction perpendicular to the pump axis in all directions; At the same time, a longitudinal vortex like stirring and mixing effect is generated between the air and the water, which rapidly increases the dissolved oxygen in the water. In aquaculture and environmental treatment of wastewater, it is necessary to aerate and decompose water bodies, as well as decompose foreign substances and sewage components.

The high-pressure blower for sewage treatment aeration is made of special materials:
1. The blades and covers of the aeration fan are made of the world's hardest ADC12 material, equivalent to the same material as Mercedes Benz wheel rims.
2. The bearings of the aeration fan adopt high-speed and high-temperature resistant imported bearings, which can rotate at 2800 revolutions per minute at 50Hz and 3450 revolutions per minute at 60Hz, without lubrication and maintenance for 150000 hours, equivalent to continuous operation for 17 years.
3. The inlet and outlet of the aeration fan are equipped with built-in sound pipes to achieve low noise.
4. Aeration fan models below 1.1KW can be used at full pressure.
5. The pressure of the aeration fan is stable, and it has been proven through practical applications in water treatment and electroplating that the stirring is uniform and the water waves roll at the same height.
6. The aeration fan has a flow rate greater than similar products under the same power and pressure.
7. The cover of the aeration fan adopts a sheet-like heat dissipation design, which is equivalent to a motorcycle engine heat dissipation device, greatly reducing the temperature during fan operation.
8. The aeration fan adopts the principle of bearing pre design, with two bearings placed at the front end of the fan blades and the rear end of the motor, achieving a good dynamic balance configuration and facilitating heat dissipation. (The reason is that there are heat dissipation fins at the front end of the fan blades for heat dissipation, while the bearings at the back end work under the built-in cooling fan of the fan, thus keeping the bearings working for a long time at low temperatures.)
9. The aeration fan adopts a special shock-absorbing foot design, which greatly reduces the vibration generated during the operation of the fan.
10. Aeration fan is economical and energy-saving. At the same power, pressure, and flow rate, the current of the aeration fan is lower than other similar products.

Sewage treatment aeration blowerMainly used in the sewage treatment industry as an aeration blower, also known as an aeration blower in some industries. It is mainly connected to the outlet of the blower through a pipeline to the bottom of the sewage treatment tank for aeration, so that the biological active substances in the sewage treatment tank can fully contact with the substances in the sewage, thereby achieving the purpose of pollution removal.

High pressure aeration blower for slaughterhouse wastewater treatmentAttention:Before the sewage treatment high-pressure fan is officially ventilated, it should undergo ventilation testing. Before ventilation, the vortex air pump should be started, and 50% of the fan's air volume should be turned on. The fan should be sent to the aeration pipeline of the biochemical tank for testing. The welding and installation quality of all nodes in the pipeline should be checked, and there should be no air leakage. If it is difficult to detect, soap water should be used for testing. At this time, special attention should be paid to the operation of the fan. For example, rotary fans cannot run without load, and the lubricating oil of the fan cannot be automatically circulated when there is no pressure. There is a risk of oil shortage operation of the fan. Therefore, during leakage testing, an appropriate amount of lubricating oil should be continuously added from the inlet to ensure normal operation of the fan.

Our services:
1. Dedicated sales engineers provide users with overall design solutions and timely help them consult and solve their use of high-pressure fans;
2. Dedicated sales and service personnel to assist users in the installation and debugging of products and hosts;
3. Promote product performance and maintenance of oil pipes to users;
4. The company has sufficient spare parts to ensure that user equipment can receive timely maintenance and repair;
5. Consult or visit users and keep records of their usage, and provide feedback to relevant departments;
6. The service principle is to serve customers with high-quality service, fast speed, and dedicated attitude.