New double-layer customized blast drying oven with upper and lower laboratory ovens

Voltage used:

220V/50HZ

Temperature control accuracy:

±1℃

Heating medium:

Stainless steel heating tube

Heating power:

2050W*2

Blast power:

15W

Number of blower units

2Taiwan

Specifications and dimensions:

Studio size:

500*500*600

Depth * Width * Height (mm)

Overall dimensions:

660*710*1700

Depth * Width * Height (mm)

Material for box production:

Overview of Machine Structure:

The air duct inside the box adopts a dual circulation system, consisting of a stainless steel multi wing centrifugal fan and a circulating air duct. The heat of the electric heater placed at the back of the box is discharged forward through the side air duct, and then sucked in by the centrifugal fan at the back after passing through the dried materialThis device adopts a high-temperature anti deformation design, usingSpecially designed high-temperature resistant blowerThe reasonable hot air circulation method effectively improves the temperature uniformity of the working chamber in the oven.

Outer wall material of the box:

Production of 1.1mm thick 08F cold rolled plate

Material of inner container:

0.9mm thicknessSUS304 # stainless steelBoard making

Box partition mesh size:

480mm*480mm

Standard number of layers for the box:

4layer*2.

Thickness and material of insulation layer:

100KHigh density aluminum silicate fiber filling(The thickness of the insulation layer is 70mm)

Outer box coating material

After rust prevention treatment, the surface is electrostatically sprayed with plastic.

New double-layer customized blast drying oven with upper and lower laboratory ovens

Door production method:

Outer wall material:

Production of 1.1mm thick 08F cold rolled plate

Door inner wall material:

0.9 mm thicknessSUS304 # stainless steelBoard making

Number of doors:

Single door, total 1 door.

Door thickness:

52mm

observation window

3Layered tempered glass

Door Buckle:

Joystick plastic heat-resistant safety handle

Door frame sealing material:

high temperature resistanceHigh density aluminum silicate fiber stripCompression seal (with good sealing performance)

Opening method:

Open from left to right.

Studio configuration:

Internal configuration:

delivery4Layered layer, standard configuration2Block mesh board.

Intake and exhaust:

Air intake:

fanbackSuction type.

Exhaust:

Aperture 32mm2One.

Blowing system:

Blowing method:

Strong pressure circulating air transport

Motor device:

boxbackInstallation at the location of the department115W/220V low-noise high-temperature ovenSpecially designed motor.

Wind turbine material:

Alloy centrifugal wind turbine.

Heating system:Stainless steel electric heater heating air circulation method

Heating element:

PT100

Heating time:

Heating rate requirement: room temperature -180 ℃ is approximately40Minutes (empty state)

Attention during testing: The testing point should be suspended in the middle position. The testing time should be at least 15-20 minutes after reaching the temperature (constant temperature state).

Electrical configuration:

1. Temperature controller:

liquid crystalTemperature controller, temperature control accuracy ± 1 ℃, with PID regulation, automatic constant temperature.

2. Time setting device:

The HS48S-99.99 timing device requires manual switching. It starts timing when the temperature reaches the set temperature and cuts off the heating power when the time reaches the set range.

3. Time alarm device:

APT/AD16 type sound and light alarm device, set time end alarm prompt.

4. Overtemperature protection device:

Install over temperature protection deviceSecond level mechanical protection effectively controls the safety of the drying process of items

5. Temperature measuring device:

1 stainless steel armored K-type resistance temperature sensing device, with temperature measurement accuracy of ± 1% FS.

6. Protection system:

Leakage protection, circuit breaker protection, motor overload protection, grounding protection.

7. Control output:

PID+SSR Solid StateControl output, high temperature control accuracy.

New double-layer customized blast drying oven with upper and lower laboratory ovens

Matters that the purchaser needs to cooperate with:

A. Provide forklifts/cranes for oven unloading and installation lifting work;

B. Keep the ground level;

C. Provide power to the air switch of the supplier's equipment control cabinet.

Installation requirements:

The distance between the front of the equipment and the wall shall not be less than 1500mm, and the distance between the left and right rear sides shall not be less than 800mm.

The user must provide an independent distribution switch and be responsible for connecting the external power supply of the equipment.

Normal working environment conditions:

Temperature: 5 ℃~45 ℃;

Relative humidity: not exceeding 85%;

There is no strong vibration or airflow around;

Power supply: AC 220V

No corrosive gases present;

Please make sure to ground it!

Thank you for your interest in our product, and we look forward to working with you!