-
E-mail
2355834892@qq.com
-
Phone
1800-2922-997,1800-2922-993
-
Address
No. 13 Lichang Road, Songmushan Village, Dalang Town, Dongguan City, Guangdong Province
Product Categories
Dongguan Tailing Electromechanical Co., Ltd
Shell rotating hollow shaft magnetic powder clutch TL-POC-A type
NegotiableUpdate on 05/01
- Model
- Nature of the Manufacturer
- Producers
- Product Category
- Place of Origin
Overview
Shell rotating hollow shaft magnetic powder clutch TL-POC-A type, flange input, hollow shaft output, hollow shaft support, shell rotating
Product Details
Shell rotating hollow shaft magnetic powder clutchTL-POC-A type, flange input, hollow shaft output, hollow shaft support, housing rotation. There are 7 standard specifications for torque, including 6Nm, 15Nm, 25Nm, 50Nm, 100Nm, 200Nm, and 400Nm. Use safe DC24V DC voltage, with a maximum allowable speed of 1800r/min and a rated slip power of 130 W、320W、450W、700W、900W、1900W、2600W。 Suitable for matching tension controllers and controlling the torque by adjusting the excitation current through the tension controller, convenient and stable.
The shell rotating hollow shaft magnetic powder clutch has good response performance, smooth operation, quiet and vibration free, and is a highly applicable and superior automatic control component. It has been widely praised and used in industries such as printing, packaging, chemical engineering, and metallurgy. As this hollow shaft magnetic powder clutch belongs to the shell rotating type, it is best to use a well ventilated metal mesh or other material to cover the entire magnetic powder clutch equipment.
1. Before formal operation or after device movement, in order to generate smooth torque, it is best to operate uniformly: in the absence of excitation, the driving side should rotate at high speed (below 1800rpm) for about 1 minute, and then set the excitation current at 1/4-1/5 of the rated value. On the one hand, rotate the driving side, and on and off for 5 seconds and 10 seconds respectively, and intermittently excite about 20 times. If there are any unclear areas, please feel free to consult our company:Miss Yang.
2. When fixing the shaft end inserted into the hollow shaft magnetic powder clutch with bolts, in order to avoid abnormal loads on the bearings inside the magnetic powder clutch, please reserve a certain axial clearance on the elastic coupling.
3. It is best to use an elastic coupling to connect the input side and shaft, and at this time, the concentricity, perpendicularity, etc. of each shaft must be controlled within the allowable range of the elastic coupling used.
4. When driving with pulleys, in order to avoid additional loads on the bearings inside the magnetic powder clutch, it is necessary to control the load within the allowable range.
5. In order to avoid the braking of the cooling stator from causing additional impact (i.e. load) on the bearings inside the hollow shaft magnetic powder clutch, it is best to set up additional retaining bracket side holes and clearances, and not tighten them in the axial direction.
The shell rotating hollow shaft magnetic powder clutch has good response performance, smooth operation, quiet and vibration free, and is a highly applicable and superior automatic control component. It has been widely praised and used in industries such as printing, packaging, chemical engineering, and metallurgy. As this hollow shaft magnetic powder clutch belongs to the shell rotating type, it is best to use a well ventilated metal mesh or other material to cover the entire magnetic powder clutch equipment.
Magnetic Particle ClutchThe inspection and handling comparison table for faults is as follows:
1. Before formal operation or after device movement, in order to generate smooth torque, it is best to operate uniformly: in the absence of excitation, the driving side should rotate at high speed (below 1800rpm) for about 1 minute, and then set the excitation current at 1/4-1/5 of the rated value. On the one hand, rotate the driving side, and on and off for 5 seconds and 10 seconds respectively, and intermittently excite about 20 times. If there are any unclear areas, please feel free to consult our company:Miss Yang.
2. When fixing the shaft end inserted into the hollow shaft magnetic powder clutch with bolts, in order to avoid abnormal loads on the bearings inside the magnetic powder clutch, please reserve a certain axial clearance on the elastic coupling.
3. It is best to use an elastic coupling to connect the input side and shaft, and at this time, the concentricity, perpendicularity, etc. of each shaft must be controlled within the allowable range of the elastic coupling used.
4. When driving with pulleys, in order to avoid additional loads on the bearings inside the magnetic powder clutch, it is necessary to control the load within the allowable range.
5. In order to avoid the braking of the cooling stator from causing additional impact (i.e. load) on the bearings inside the hollow shaft magnetic powder clutch, it is best to set up additional retaining bracket side holes and clearances, and not tighten them in the axial direction.
The following is the specification and size parameter table of our TL-POC-A type magnetic powder clutch with a rotating hollow shaft shell:
Similar Product Recommend
