Shanghai Kaiyuan Automation Technology Co., Ltd
3007052287@qq.com
13482468385
Building 1, No. 188 Xinghuo Road, Qingcun Town, Fengxian District, Shanghai
Inline， Bus coupler, PROFIBUS DP, D-SUB-9 female connector, digital input: 8, 24 V DC, connection technology: 3 wires, digital output: 4, 24 V DC, 500 mA, connection technology: 3 wires, local bus transmission rate: 500 kBit/s/2 MBit/s, protection level: IP20, including Inline connector and marking strip
The bus coupler with built-in I/O is specifically designed for PROFIBUS networks and can be connected to Inline I/O systems. This bus coupler can connect up to 61 Inline devices. Provide supporting GSD files for integrating the Inline site into the programming system.
| Size chart |  |
| width | 80 mm |
| height | 119.8 mm |
| depth | 71.5 mm |
| Notes on Dimensional Data | Pin connector specifications |
| Usage restrictions | |
| CCCex Explanation | It is not allowed to be used in potential explosive areas in China. |
| PROFIBUS DP | |
| number of interfaces | 1 |
| connection method | D-SUB-9 female connector |
| transmission speed | 9,6 kBit/s . .. 12 MBit/s |
| Inline local bus | |
| connection method | Inline data bridging block |
| transmission speed | 500 kBit/s/2 MBit/s (automatic detection, no system combination) |
| System limitations | |
| Number of supported devices | 63 (per station) |
| The number of devices that can be connected to the local bus | 61 (onboard I/O consists of two devices) |
| Number of devices with parameter channels | 16 |
| Number of branch terminals supported with remote bus branches | 0 |
| I/O response time | Typical value of 4 ms (parallel I/O; Transmission speed PROFIBUS 1.5 Mbps, local bus 500 kbps) |
| module | |
| Hexadecimal ID encoding | 0B50 |
| Enter address area | 8-bit (or 1-byte, select from GSD file) |
| Output address area | 4 bits (or 1 byte, select from GSD file) |
| Register length | 16 bits |
| Numerical quantity: | |
| input name | digital input |
| Input instructions | EN 61131-2 Type 1 |
| Input quantity | 8 |
| connection method | Inline connector |
| connection system | 3 lines |
| input voltage | 24 V DC |
| Input voltage range, '0' signal | -30 V DC . .. 5 V DC |
| Input voltage range, '1' signal | 15 V DC . .. 30 V DC |
| Rated input voltage UIN | 24 V DC |
| Rated input current UIN | Typical value 3 mA |
| Typical input current for each channel | Typical value 3 mA |
| Typical response time | Approximately 500 µ s |
| Signal switching delay time from 0 to 1 | 2.9 ms |
| 1 to 0 signal switching delay time | 2.9 ms |
| Numerical quantity: | |
| Output Name | digital output |
| connection method | Inline connector |
| connection system | 3 lines |
| Output quantity | 4 |
| protection circuit | Short circuit and overload protection; Output driver freewheeling circuit |
| output voltage | 24 V DC -1 V (at rated current) |
| Output current of each module | 2 A |
| Rated output voltage | 24 V DC |
| Output current when disconnected | 10 µ A (voltage can be measured without load even if no output is set). ) |
| Rated load, inductive | 12 VA (1.2 H，48 Ω) |
| Rated load, indicator light | 12 W |
| Rated load, resistive | 12 W |
| Reverse voltage resistant to short pulses | Prevent reverse voltage |
| Overload behavior | Auto-restart |
| Inductive overload action | Output may be damaged |
| Behavior when voltage is turned off | No delay between output and power supply |
| Signal delay | Typical value 2.9 ms |
| Overcurrent shutdown | Minimum 0.7 A |
| Product Type | I/O components |
| Product Series | Inline |
| type | module |
| Scope of supply | Including Inline connectors and marker strips |
| Number of channels | 12 |
| Diagnostic information | Digital output short circuit or overload is |
| What is the sensor power failure | |
| What is the power failure of the actuator | |
| Insulation characteristics | |
| Overvoltage category | II (IEC 60664-1，EN 60664-1) |
| pollution level | 2 (IEC 60664-1，EN 60664-1) |
| Power consumption under rated conditions | 23.5 VA |
| electric potential | |
| power consumption | Typical value 1.7 W (for the entire device) |
| Potential: Bus coupler power supply UBKCommunication power supply UL(7.5 V) and analog power supply UANA(24V) Powered by a bus coupler power supply. | |
| power supply voltage | 24 V DC (via Inline connector) |
| Power supply voltage range | 19.2 V DC... 30 V DC (including all tolerances, including ripple) |
| current consumption | 0.98 A (connected number of I/O modules) |
| Minimum 80 mA (without connected I/O module) | |
| Potential: Communication power supply (U)L) | |
| power supply voltage | 7.5 V DC |
| Potential: power supply for analog module (U)ANA) | |
| power supply voltage | 24 V DC |
| Power supply voltage range | 19.2 V DC... 30 V DC (including all tolerances, including ripple) |
| Potential: Main circuit (U)M）Power supply | |
| power supply voltage | 24 V DC (via Inline connector) |
| Power supply voltage range | 19.2 V DC... 30 V DC (including all tolerances, including ripple) |
| current consumption | 8 A DC |
| Minimum 3 mA (not connected to peripheral devices) | |
| Potential: segmented circuit power supply (US) | |
| power supply voltage | 24 V DC (via Inline connector) |
| Power supply voltage range | 19.2 V DC... 30 V DC (including all tolerances, including ripple) |
| current consumption | 8 A DC |
| Minimum 3 mA (not connected to peripheral devices) | |
| Electrical isolation/voltage range isolation | |
| Test voltage resistance: PROFIBUS interface/communication power supply (U)BK、UL、UANA) | 500 V AC， 50 Hz， 1 min. |
| Test voltage resistance: PROFIBUS interface/I/O (U)M、US) | 500 V AC， 50 Hz， 1 min. |
| Test voltage resistance: PROFIBUS interface/functional grounding | 500 V AC， 50 Hz， 1 min. |
| Test voltage resistance: Communication power supply (U)BK、UL、UANA)/I/O (UM、US) | 500 V AC， 50 Hz， 1 min. |
| Test voltage resistance: Communication power supply (U)BK、UL、UANA）/Functional grounding | 500 V AC， 50 Hz， 1 min. |
| Test voltage resistance: I/O (U)M、US）/Functional grounding | 500 V AC， 50 Hz， 1 min. |
| Connection technology | |
| Connection Name | Inline connector |
| Wire connection | |
| connection method | Pull back spring connection |
| Rigid wire cross-section | 0.08 mm² . .. 1.5 mm² |
| Cross section of flexible wire | 0.08 mm² . .. 1.5 mm² |
| Connectable guide cross-section AWG | 28 . .. 16 |
| Stripping length | 8 mm |
| Inline connector | |
| connection method | Pull back spring connection |
| Cross section of hard wire | 0.08 mm² . .. 1.5 mm² |
| Cross section of flexible wire | 0.08 mm² . .. 1.5 mm² |
| Connectable guide cross-section AWG | 28 . .. 16 |
| Stripping length | 8 mm |
| environmental conditions | |
| Environmental temperature (operating) | -25 °C . .. 60 °C |
| protection level | IP20 |
| Air pressure (operation) | 70 kPa... 106 kPa (up to an altitude of 3000 meters) |
| Air pressure (storage/transportation) | 70 kPa... 106 kPa (up to an altitude of 3000 meters) |
| Environmental temperature (storage/transportation) | -25 °C . .. 85 °C |
| Allow humidity (operation) | 10 % . 95% (no condensation) |
| Allow humidity (storage/transportation) | 10 % . 95% (no condensation) |
| protection level | III (IEC 61140，EN 61140，VDE 0140-1) |
| Installation Type | DIN rail installation |
