FP small fluoroplastic centrifugal pump

NegotiableUpdate on 03/29

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

1、 Overview of FP Fluoroplastic Centrifugal Pump: The FP type reinforced polypropylene centrifugal pump series products all use mechanical seals and introduce international advanced processes and technical formulas. They all use CFR-PP (reinforced polypropylene) as the material of the pump. Among plastic pump products in the same series, it fully demonstrates its advanced structure, light weight, small volume, and long service life. It is widely used in chemical, food, pharmaceutical, electroplating, papermaking, environmental protection, water treatment and other departments to transport corrosive liquids such as acids, alkalis, and salts. Among them, the 104 type adopts 220V voltage and can be used for household selection. 2、 Meaning of FP type fluoroplastic centrifugal pump model 3. Troubleshooting of FP type fluoroplastic centrifugal pump. Causes of fault forms ..

Product Details

1、 Overview of FP Fluoroplastic Centrifugal Pump

The FP type reinforced polypropylene centrifugal pump series products all adopt mechanical seals and introduce international advanced processes and technical formulas. CFR-PP (reinforced polypropylene) is used as the material of the pump. Among plastic pump products in the same series, it fully demonstrates its advanced structure, light weight, small volume, long service life and other characteristics. It is widely used in chemical, food, pharmaceutical, electroplating, papermaking, environmental protection, water treatment and other departments to transport corrosive liquids such as acid, alkali, salt, etc. Among them, the 104 type adopts 220V voltage and can be used for household selection.

2、 The significance of FP type fluoroplastic centrifugal pump model

3、 Troubleshooting of FP Fluoroplastic Centrifugal Pump

Fault form	root cause	exclusion method
The pump cannot produce liquid	Pump reversal Leakage in the inlet pipeline There is too little liquid stored in the pump chamber The suction distance is too high Bottom valve leakage Impeller obstructed and unable to rotate	Change the motor wiring Eliminate air leakage Increase the storage capacity Lower the installation position of the pump Clean the bottom valve Clean the pump casing and impeller
Insufficient data	The suction pipe diameter is too small Impeller channel blockage Head too high There is air leakage in the suction pipeline Damaged impeller	Replace the liquid inlet Clean the impeller Turn up the outlet valve Eliminate air leakage Replace the impeller
Low head	Too much traffic The speed is too low	Turn down the outlet valve Restore rated speed
Low noise level	There are debris inside the pump Friction between rotating parts and fixed parts Severe wear of the shaft	Check and clean adjust the gap Replace the pump shaft
leakage	Loose fixing screws of pump casing Severe wear of mechanical seal	Tighten the screws Replace the mechanical seal

4、 Performance parameter table of FP type fluoroplastic centrifugal pump

model	caliber		traffic m3/h	head m	suction lift	speed r/min	voltage v	motor Power kw
model	Import	Export	traffic m3/h	head m	suction lift	speed r/min	voltage v	motor Power kw
FP20-15-60 (106)	20	15	1	5	3	2900	380	0.12
FP20-20-90 (105)	20	20	3	6	3		380	0.37
FP32-25-100 (104)	32	25	5	7	6		220	0.55
FP32-25-105 (103)	32	25	6.3	8	6		380	0.75
FP32-25-110	32	25	8	14	6		380	1.1
FP40-32-125 (102)	40	32	12.5	20	6		380	1.5
FP50-40-145	50	40	13	22	6		380	2.2
FP65-50-150 (101)	65	50	25	25	6		380	4
50FP-22	50	40	13	22	6		380	2.2
65FP-25	65	50	20	25	6		380	4
80FP-28	80	65	50	28	4		380	5.5
80FP-32	80	65	50	32	4		380	7.5